Xantrex RS3000 Manual do Utilizador Página 108
- Página / 128
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Battery Charging Reference
B–4 975-0170-01-01
Float Charge
In the third stage—the float charge—which is a maintenance mode, the
output voltage of the charger is reduced to a lower level, typically about
13.5 (V
F1
) volts to maintain the battery’s charge without losing electrolyte
through gassing.
With AC reconnected during this stage, the unit will return to the float
stage.
Equalization Charge
The equalization charge must be manually initiated from the System
Control Panel because it is not required each time the battery is recharged.
Equalization is a deliberate overcharge designed to return each cell to
optimum condition by reducing sulfation and stratification in the battery.
The overcharge helps the battery to reach and maintain peak capacity.
An equalization charge should be performed only on flooded, vented
(non-sealed or “wet”) batteries. It should be performed only if
recommended by the battery manufacturer and only as often as specified.
After initiating an equalize charge cycle, the charger will always execute
a bulk and absorption charge stage before starting the actual equalize
charge stage. The equalize charge stage has a default current and voltage
setpoint at 10% of C in Ah and 15.5 VDC, respectively. During the
equalize charge stage, the charger will produce current equal to the
current setpoint as long as the battery voltage is still less than the voltage
setpoint. When the voltage setpoint is reached, the charger will change its
current output to keep the battery voltage steady at the voltage setpoint
level.
There is a timeout (default is 1 hour) for the equalize charge stage. The
charger will exit equalize after the timeout has occurred, even if the
voltage setpoint has not been reached. Should another equalize cycle be
required, it has to be manually initiated from the System Control Panel.
Should an AC reconnect occur during the equalize charge stage, the
charger will return to the float/no-float charge stage, depending on which
one is selected.
- Operation Guide 1
- About This Guide 5
- Conventions Used 6
- Important Safety Instructions 9
- Explosive Gas Precautions 11
- FCC Information to the User 12
- Contents 13
- Configuration 14
- Troubleshooting 15
- 975-0170-01-01 xv 17
- Introduction 19
- Premium Power and Ease of Use 20
- How RS3000 Works 21
- Charging 22
- Xanbus System 23
- Xanbus Enabled 23
- RS3000 Features 25
- Figure 1-3 26
- Table 1-2 26
- Side Panel Features 27
- CAUTION: Equipment Damage 27
- Table 1-3 28
- DC Terminal Covers 29
- Battery Temperature Sensor 29
- Operation 31
- Important: 32
- On Start Up 34
- System Start-up Check 35
- Operating in Invert Mode 36
- Power Output 37
- Operating in Charger Mode 38
- WARNING: Explosive gases 40
- Equalizing Batteries 41
- Power Share 42
- Faults and Warnings 44
- System Modes 45
- Operating Mode 46
- Power Save Mode 46
- Operating 47
- [Advanced] 47
- 2–18 975-0170-01-01 48
- 975-0170-01-01 2–19 49
- Hibernate Mode 50
- System Control Panel 52
- System Menu Map 53
- Viewing the System Screen 54
- [*Enabled] 55
- Clear Faults 57
- 3–8 975-0170-01-01 58
- RS3000 Menu Structure 59
- RS3000 Device Menu 60
- AC Input1 and AC Input2 61
- RS3000 Menu (Basic) 62
- [Enabled] 64
- [Flooded] 64
- Equalization? 66
- Batt Size 67
- RS3000 Menu (Advanced) 68
- Equalize 69
- Load Sense 69
- View Device Info 69
- Basic Menu 69
- Sub-Menus 70
- Lo DC Volt 71
- Batt Type 71
- Sense Below 71
- Sense Interval 72
- # Chg Stages 72
- Eqz Volts 73
- Force Charge 73
- Lo AC Volt 74
- Lo AC Freq 75
- Hi AC Volt 75
- Hi AC Freq 76
- View Fault Log 77
- View Warning Log 77
- View Event Log 78
- Restore Defaults 78
- Info menu appears 79
- Figure 3-15 79
- Restore Defaults Warning 79
- Warning Types 83
- Troubleshooting Reference 84
- 975-0170-01-01 4–5 85
- 4–6 975-0170-01-01 86
- Warning Messages 87
- Table 4-3 88
- Fault Messages 91
- Table 4-4 92
- Inverter Applications 97
- Searching 98
- Specifications 99
- Inverter Specifications 100
- Charger Specifications 101
- Environmental Specifications 102
- Regulatory Approvals 103
- Fan Operation 103
- -10 0 10 20 30 40 50 60 104
- Ambient Temperature (°C ) 104
- Reference 105
- Battery Charging 105
- Charge Algorithm Stages 106
- Bulk Charge 107
- Absorption Charge 107
- Float Charge 108
- Equalization Charge 108
- Charge Algorithm Graph 109
- Charge Algorithm Definitions 109
- Battery Charger Interruption 110
- Terminology 111
- Glossary 112
- Abbreviations 116
- Warranty and Return 119
- Information 119
- Disclaimer 120
- Return Procedure 121
- Out of Warranty Service 122
- Information About Your System 122
- Xantrex Technology Inc 128
Manuais e produtos relacionados com Adaptadores e conversores de corrente Xantrex RS3000
(47 páginas)Rexel 2103026EU manuals
Owner’s manuals and user’s guides for Paper shredders Rexel 2103026EU.
We providing 1 pdf manuals Rexel 2103026EU for download free by document types: Datasheet
Comentários a estes Manuais